Basic Bissell Carpet Cleaner Troubleshooting
Troubleshooting brushes
If your brushes are not turning, check the pump belt. You will need a flat-head screwdriver to pry in the slots to see if the belt is removed or broken. Replace the pump belt is a broken. If the belt seems fine, inspect the brush. A small object could have been sucked up and jammed the brush. Replace the brush if it bent or worn down. Check this too: Roomba Troubleshooting & How to Guide
Reduced or no spray
If your spray is less than stellar, first take off all hoses from the heater and clean them, Check the nozzles for clogs. If there is hair or grime on the nozzles, use a tiny cotton swab and clean out the thin housing. Make sure there is sufficient water in each tank, The detachable O-rings that secure the straw can cause leakage, so ensure they are tight and sit well.
Not sucking up water
If your Bissell carpet cleaner is not sucking up water properly, make sure the dial is set to floor cleaning. Jiggle the tank to make sure it is making a good connection to the machine.
Bissell carpet cleaner brushes not spinning
The possible cause for Brushes not spinning/turning on your Bissell carpet cleaner is the brush belt or pump belt is off or is broken. To fix the problem, you need to first turn the machine off and unplug it from the socket. To check if a pump belt has broken, you need a flat head screwdriver. Then follow these instructions:
Insert the blade end into the lower slot of the Belt Access door to release the lower snap. If necessary, insert the blade end into the upper slot to release the upper snap.Examine the belt for breakage. Replace the pump belt is broken.
To remove the broken pump belt follow these steps: Follow the instructions below to install the replacement pump belt: Check this too: How to Clean Legos
Bissell carpet cleaner not picking up water
There are several reasons why your Bissell carpet cleaner is not picking up water:
Bissell carpet machine leaks water
If your Bissell ProHeat 2X Revolution Pet Carpet Cleaner appears to be leaking, follow these steps to resolve:
After spraying the solution by pulling the trigger, perform a few dry strokes before turning the machine offTurn off and unplug the machineRemove the clean tank. Check for cracks, warping, or damage. If cracked, warped, or damaged, order a new clean water tank.Makes sure the gasket at the bottom of the clean tank is working properly and water is only coming out when the valve is pushed upward. If the bottom of the clean tank is damaged or, not working properly, order a new clean water tank.Water may be caught in space between the tank and the tank’s handle. With the cap twisted ON tightly hold your tank at an angle, over a sink or drain, so any extra water can pour out of the space.Wipe the tank dry with a cloth.Reseat the Clean Water Tank. A fully clean water tank should sit all the way into the machine with the back of the tank flush with the handle.Remove the dirty water tank and fill with water over the sink from the rubber opening at the top. If dirty water tank is leaking, a new one should be ordered.Move the machine to a dry area of carpet- do not press the trigger. Make sure clean water tank is filled and on the machine.Remove the handle of the machine, then reconnect itLeave it in the same spot for 30 secondsMove the machine to a new spot. Has the issue resolved? Contact Bissell if there is a significant puddle under where the machine was sitting.
Bissell carpet cleaner won’t turn on
If you have no power going into your Bissell SpotClean Proheat carpet cleaner, try the following troubleshooting tips to fix the problem:
Start by plugging in your machine to a grounded outlet.To power the machine ON, press the power on button. The “I” is power on and “O” is power off.If there is still no power, unplug your machine from the wall.Check the entire length of the power cord, and discontinue use if there is any damage.Check to see if the outlet is working. Test the outlet by plugging another device like a cell phone charger.Check for a tripped breaker. Often homes have several outlets on the same breaker, and the breaker can be tripped if multiple appliances are plugged into those outlets.Try using an outlet in a different area or resetting any tripped breakers.SpotClean is designed with a thermal protector shutting it down to protect from overheating in the event of a clog or blockage. Unplug and check the end of the hose, tool, and inside the dirty water tank stack and remove clogs.Let the unit sit unplugged for 30 minutes after removing clogs for the thermal protector to cool and reset automatically. Then test in a working outlet.
How to take apart a Bissell ProHeat carpet cleaner
To take apart your Bissell Proheat 2X Revolution Pet Pro cleaner, you will need a Philips head screwdriver. Then follow these instructions:
First, make sure your machine is turned off and unpluggedRemove the clean water tankNow remove the screw in the back of the handle with a Philips screwdriver by twisting counterclockwiseBe sure not to lose the screw from the handle, you will need it when it is time to put your machine back togetherUsing your thumb as leverage, pull outward each side of the carry handle to removeNext, use a flathead screwdriver to pry uo both sides of the plastic collar at the base of the handleThen pull up on the upper handle until it releases from the machineYou now have your machine disassembled
How to reset a Bissell carpet cleaner
If your PowerGlide 1305 series vacuum becomes clogged, the vaccum is equipped with a brush shut off to prevent damage from occurring. If this were to happen, follow these steps to reset your brush roll:
Turn the vacuum to the off position.Turn the brushroll switch to the off position.Unplug the vacuum from the electrical outlet.Lay the vaccum down and check for any major clogs in the brush chamber. Once the brush roll is free of debris, return the vaccum to the upright position.Locate the brush reset button on the lower back right of the vaccum.Press the button to reset the brushroll.To ensure the brush has been reset, plug thevaccum back into the electrical outlet. Turn on the vacuum detent the vacuum to begin cleaning. Turn the brushroll on. The brush should start to rotate when the vacuum is leaned back and the brushroll is on.
Why is there no water coming out of my Bissell carpet cleaner
If there is reduced spray or no spray coming out of your Bissell carpet cleaner, it is because of the following possible reasons:
How to unclog a Bissell carpet cleaner
If one or more of the lines in your Bissell carpet cleaner becomes clogged, the unit stops working. To unclog, you need to take the assembly apart and clean the lines, ensuring they are not tangled, to return the carpet cleaner to its proper level of functioning. To unclog a Bissell ProHeat carpet cleaner follow these steps: Check this too: Can you put a refrigerator on the carpet?
How to clean Bissell Proheat Cleaner filter
You need to clean out the flow indicator filter each time it used to ensure best cleaning performance.
Unscrew the flow indicator cap.Lift out the red rotor and white filter.Rinse all three parts in tap water.Replace the filter and rotor.Replace the flow indicator cap; turn until snug. Do not over-tighten.
